All Filaments

PLA+

Tougher, less brittle PLA blend. Slightly higher temp and impact resistance.

beginnerStandard

Specifications

Nozzle Temperature
200-230°C
Bed Temperature
50-65°C
Max Print Speed
80 mm/s
Drying Temp
45°C
Drying Time
4 hours
Enclosure
Not needed
Moisture Sensitive
No

Signs of Moisture

Watch for these signs
  • popping during extrusion
  • stringing worse than usual
  • weak layer adhesion
  • rough surface finish

Storage Requirements

Temperature
15-25°C
Max Humidity
30% RH
Container
resealable bag with silica gel desiccant

Known Issues

Higher temps required vs PLA

Cause: Toughened additives need more heat to flow cleanly

Fix: Run 5-10°C hotter than your usual PLA temperature

Stringing

Cause: Slightly stickier melt than standard PLA

Fix: Increase retraction distance by 0.5mm and lower travel temperature

Best For

everyday functional partstools and jigstoysparts that need a bit more durability than PLA

Not Good For

high-temperature environmentsparts in direct sun for long periods

Compatible Build Surfaces

PEI
glass with glue stick
magnetic spring steel

Post-Processing Options

sanding
painting
drilling and tapping

Popular Brands

Brand-specific recommended temps and quirks. Click through for the full settings page.

15 brands found

Artillery

Excellent
N 220°C B 65°C

Recommended 220°C nozzle / 65°C bed. Max volumetric flow ~21.0 mm³/s. Single-source profile (orcaslicer); verify before relying on it.

View settings

Generic

Good
N 215°C B 60°C

Recommended 215°C nozzle / 60°C bed. Single-source profile (cura); verify before relying on it.

View settings

ideagen3D

Good
N 210°C B 60°C

Recommended 210°C nozzle / 60°C bed. Single-source profile (cura); verify before relying on it.

View settings

Numakers

Good
N 210°C B 60°C

Recommended 210°C nozzle / 60°C bed. Single-source profile (spoolman); verify before relying on it.

View settings

Ultimaker

Good
N 215°C B 60°C

Recommended 215°C nozzle / 60°C bed. Single-source profile (cura); verify before relying on it.

View settings

XYZprinting

Good
N 210°C B 45°C

Recommended 210°C nozzle / 45°C bed. Single-source profile (cura); verify before relying on it.

View settings

3D-Fuel

Fair
N 220°C B 60°C

Recommended 220°C nozzle / 60°C bed. Single-source profile (spoolman); verify before relying on it.

View settings

Anycubic

Fair
N 210°C B 55°C

Recommended 210°C nozzle / 55°C bed. Single-source profile (spoolman); verify before relying on it.

View settings

Deeplee

Fair
N 220°C B 60°C

Recommended 220°C nozzle / 60°C bed. Single-source profile (spoolman); verify before relying on it.

View settings

Elegoo

Fair
N 210°C B 60°C

Recommended 210°C nozzle / 60°C bed. Single-source profile (spoolman); verify before relying on it.

View settings

eSUN

Fair
N 220°C B 60°C

Recommended 220°C nozzle / 60°C bed. Single-source profile (spoolman); verify before relying on it.

View settings

Filament Unger

Fair
N 220°C B 60°C

Recommended 220°C nozzle / 60°C bed. Single-source profile (spoolman); verify before relying on it.

View settings

DIALED-IN SETTINGS

FixMyPrint generates exact slicer settings for PLA+- calibrated for your printer and slicer in seconds.

Generate Settings for PLA+